home *** CD-ROM | disk | FTP | other *** search
- Path: ringer.cs.utsa.edu!runner!dparr
- From: dparr@runner (Doug Parr)
- Newsgroups: comp.sys.amiga.hardware
- Subject: A3000 SCSI
- Date: 7 Feb 1996 07:24:43 GMT
- Organization: The Unversity of Texas at San Antonio
- Distribution: world
- Message-ID: <4f9k3r$h8d@ringer.cs.utsa.edu>
- NNTP-Posting-Host: runner.jpl.utsa.edu
-
-
-
- I have been following this newsgroup for only about a month now and I must
- say that the individuals who post to it on a regular basis are a very
- informative, knowledgable, and professional group of people. Special thanks
- to Gene Heskitt, Warren Block, Dave Hainey (pardon me if I misspelled
- anyones name).
-
- So based on the knowledge I have gained I set about to upgrade my A3000. I
- thought I would share some info.
-
- I replaced the clock battery since upon inspection it looked like there was
- some corrosion. The battery is located under the expansion boards on the
- left as you look at the front of the computer. It is soldered into the
- motherboard , but not too difficult to un-solder if you understand the basics
- of soldering.
-
- Location: BT190
- Amiga Battery: 3/GP60K NI-CAD
- Source: Radio Shack
- Part#: CNB-3/V60R
- Express Order#: 10048155
- Price: $11.99
-
- Replaced Ramsey-04 with Ramsey-07. Can anyone tell me what this chip does?
- I assume it has to so with RAM access.
-
- Replaced Super DMAC-02 with Super DMAC-04. I assume that stands for Direct
- Memory Access Controller?
-
- Replaced the the SCSI chip WD33c93a-04 with -08.
-
- I had previously replaced the Buster with -11 when I put in a GVP PhonePak.
-
- Source: Paxtron
- 28 Grove St.
- Spring Valley, NY 10977
- 914-578-6522
- Ramsey - $29.95
- DMAC - $44.50
- WD - $32.50
-
- I got reasonable service from them. After my checked cleared the order came
- within a few days. Some chips are cheaper and some are more expensive
- depending on the vendors. I just decided to buy from one source.
-
- I did not have a tool for pulling the Ramsey and DMAC, so I got a large
- bolt, ground the markings off the head, applied super glue, stuck it to the
- top chip, let the glue dry and then pulled straight up with one hand while
- holding the socket with the other. Crude, but effective.
-
- Some of you skilled electronic technicians may cringe at the method, but
- hey, I am just a simple guy.
-
- I checked the voltage on pin 25 of the DB25 SCSI external connector and
- there is +5 volts there; so the 1N914 diode at location D800 is oriented
- correctly. I have motherboard rev 9/02 and daughter board rev 6.3.
-
- My motherboard does not have SCSi termination on it. However, it does have
- sockets for 3 terminators right by the SCSI connector. Evidently some motherboards
- have termination, either socketed or soldered.
-
- I now have an internal 100MB Quantum, two 311MB Seagate ST4376NV drives, and a
- Viper 2150S tape backup; all working very well.
-
- The Seagates are from an old Novell network and are actually CDC Wren IV
- full-height 5.25" drives; and heavy as hell. They were top of the line
- drives a few years back and sold for about $2000 I think. But they were free,
- have a 17ms access speed, and can be used as weapons in case of an
- emergency.
-
- So about that debate about the A3000 following SCSI spec or not:
-
- I do not have termination on the motherboard.
-
- With no external and drives, no termination on the motherboard, and one
- internal drive terminated, my system had worked reliably for years. That
- short internal cable allows this cheat, and while not spec, evidently
- works.
-
- Upgrading the chips and understanding SCSI termination and the A3000
- peculiarities allows for a reliable SCSI chain.
-
- Hope this helps.
-
-
-
-